Scytek-electronics VISIONGUARD 6000 Manual de usuario

VISIONGUARD6000VEHICLE SECURITY SYSTEMWITH BUILT-IN CAMERAAND A REMOTE START PRODUCT MANUAL

Page 6 - VisionGuard 6000Camera Features

VisionGuard 6000 - Page 7

Page 8 - VisionGuard 6000Remote ArmingThe system monitors 6 independent areas (zones) while armed: doors, hood, trunk, shock sensor, optionalsensor i

VisionGuard 6000 - Page 9Tamper AlertIf the system was triggered while away, the LED will flash to indicate which zone triggered the system afterdis

Page 10 - VisionGuard 6000Panic ModeIn the event of an emergency the transmitter’s remote Panic feature can be used to instantly trigger thealarm.To

VisionGuard 6000 - Page 11To set the Emergency Override Code:1. Turn on ignition.2. Within 5 seconds, press the valet switch 5 times.· The siren wil

Page 12 - VisionGuard 6000Remote StartingTo Remote Start the System:1. Be sure the system is not in Valet Mode.2. Press and hold Button 4 for three

VisionGuard 6000 - Page 13Turbo Timer FeatureThe Turbo Timer feature allows vehicles with turbocharged engines to remain running after the ignition

Page 14 - VisionGuard 6000Extended FeaturesIgnition Door LockingFor added safety, the Ignition Door Locking feature allows vehicles equipped with po

VisionGuard 6000 - Page 151. Thoroughly read and become familiar with the installation instructions before beginning the installation.2. Review sys

Limited Lifetime WarrantyThis vehicle security system is warranted to the original purchaser, to be free from defects inmaterial and workmanship. Th

Page 16 - VisionGuard 6000Mounting the Control UnitThe control unit must only be mounted in the interior of the vehicle. Do not mount the main unit

VisionGuard 6000 - Page 17System Wiring6-Pin Starter HarnessPin 1 RED WIRE A: Main Power Input A (+). Connect to the battery or constant power wire

Page 18 - VisionGuard 6000when the door is open. This type of door circuit is usually found on Ford vehicles.Pin 12 GREEN WIRE: Negative Door Input

VisionGuard 6000 - Page 19Jumper SelectionCarefully separate the top and bottom halves of the main unit case. Once the cover is removed, the parkin

Page 20 - VisionGuard 6000Entering System ProgrammingThis system is compatible with both the optional LCD transmitter or the standard AM transmitter,

VisionGuard 6000 - Page 215. Ignition Door Unlocking. Selects whether or not the system automatically unlocks the doors whenthe ignition is turned o

Page 22 - VisionGuard 60008. Passive Door Locking. Selects whether or not the system will automatically lock the doors duringPassive Arming and Auto

VisionGuard 6000 - Page 23Diesel Engine. Sets the engine type for Diesel and monitors the glow plug input to make sure the glowplugs are warm before

Page 24 - VisionGuard 6000Wiring DiagramsTO POSITIVEDOME LIGHT+12VBlack/White(-) DOME LIGHTOUTPUTTO NEGATIVEDOME LIGHT+12VBlack/White(-) DOME LIGHTO

VisionGuard 6000 - Page 25Negative TriggerPositive TriggerReverse Polarity VacuumAdding ActuatorsFollow the diagrams below for connecting basic door

1. About Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 12. Remote Tra

Page 26 - VisionGuard 6000Two Stage Door Lock DiagramsTwo Stage Negative TriggerTwo Stage Positive TriggerThe VisionGuard 6000 is equipped with a

VisionGuard 6000 - Page 27Two Stage Door Lock Diagrams cont’dTwo Stage Reverse PolarityTwo Stage Adding Actuators

Page 28 - VisionGuard 6000FCC ID: OARRXAM2000This device complies with Part 15 of FCC Rules.Operation is subject to the following two conditions:1) T

VisionGuard 6000 - Page 29Starter DiagnosticsStarter doesn’t start and Side Lights flash:3 Times - Engine RPM not detectedHood Trigger is active4

Page 30 - VisionGuard 6000

VisionGuard 6000 - Page 31

ScyTek Electronics11627 Cantara StreetNorth Hollywood, CA 91605© ScyTek Electronics 2005 VisionGuard 6000 r3 11/05Wiring DiagramScyNetBlue Start (-)G

The ScyTek VisionGuard 6000 is a combination vehicle security and remote starting system featuring a built-in "ScyNet Network Port" that all

Standard Remote Transmitter DescriptionThe VisionGuard 6000 is compatible with the optional 5-button Remote Transmitters used to control systemoperati

Adding/Replacing Transmitters To replace lost or stolen transmitters or to add additional transmitters into the system, have all desiredtransmitters r

Page 4 - VisionGuard 6000True Color 2-way Camera Ready Remote Transmitter DescriptionThe VisionGuard 6000 True Color 2-way LCD remote transmitter, is

VisionGuard 6000 - Page 54. Turn off the ignition key.5. Repeat steps 1-4 to add an additional 2-way transmitter.System ConfirmationThe 2-way tran